Share on

Metal Detection and X-Ray on Seafood Lines: What Buyers Ask

News

CN

Tbes Editorial Team

In short

A metal detector finds metal in the product. X-ray also finds dense non-metal objects such as glass, ceramic, bone or dense plastic. No universal checking interval exists, so the site sets its own. Ask five things: where the detector sits, which test pieces it uses, how often it is verified, what happens to rejects, and which records exist.

What do metal detectors and X-ray each find?

An industry article on calibration standards describes the test pieces used to check each type of equipment. Metal detectors are tested with ferrous, non-ferrous and stainless steel pieces (grades 316, 304 and 310 are named), each embedded in a non-metallic carrier. X-ray systems are tested with ceramic, glass, bone, rubber or dense plastic pieces. The article adds that X-ray can catch contaminants that a metal detector misses.

Metal detection and X-ray compared (from the cited industry article)
EquipmentTest pieces namedPoint for the buyer
Metal detectorFerrous, non-ferrous, stainless steel (316, 304, 310) in a non-metallic carrierAsk which metal types and which stainless grade are tested
X-rayCeramic, glass, bone, rubber, dense plasticAsk which non-metal materials are tested
BothA test piece passed through the normal product flowAsk whether the test uses the real product and pack

The article gives no test-piece size that applies to every product, and we found no authoritative standard value. The size depends on the equipment, the product and the pack, so agree it with the supplier. Naming a brand of detector does not answer the question. Showing the test pieces and the sizes in the written procedure does.

Why is detection treated as a control point?

Under HACCP, a hazard analysis lists the hazards in a process and decides which steps control them. A step that controls a significant hazard becomes a critical control point, with a critical limit, monitoring, corrective action and verification. Some plants set metal detection as a critical control point and others treat it as a prerequisite control. Which one applies is a result of the plant's own hazard analysis. This is a general description of HACCP, not a statement about any one site.

The industry article describes calibration of the equipment as a verification step for the control point. That wording helps a buyer. It means the test-piece check is not a courtesy to the customer. It is the evidence that the control works. Ask the supplier to show where metal detection appears in its hazard analysis and what the critical limit says, in its own words.

Where on the line does the detector sit?

We found no source that sets a rule for detector position, so treat this as a question to ask. Metal that enters the product after the detector is not caught by it. Ask for the line diagram and ask which steps lie downstream of the detector. Then ask whether the detector checks product before packing, packed cartons or both. For IQF product, ask whether the inner bag and the carton are inside the detector's field. The answers show how much of the process the check covers.

How often is the equipment verified?

The industry article lists schedules that sites use: at start-up each day, every hour, at changeovers, at the end of a shift, and weekly or monthly for a full check. It also states that no required interval is set. The article says BRCGS has clauses on foreign body detection equipment and on verifying it with test pieces, and that SQF requires a documented calibration programme. Read these as the article's account of the schemes, and check the scheme text if a clause number matters to you.

Schedule examples named in the article, with the question each prompts
Check pointExample from the articleQuestion to ask
Start of productionDaily at start-upIs the line allowed to run before the check passes?
During productionHourlyWhat interval does the plan set, and why?
Product changeAt changeoversIs the check repeated for each product and pack size?
End of shiftAt the end of a shiftWhat happens to product since the last good check if one fails?
Full checkWeekly or monthlyWho performs it, and is it recorded?

Our guide to what HACCP, ISO 22000 and BRCGS each cover explains how a scheme certificate relates to a plant's own procedures. A scheme clause tells you that a procedure must exist. The procedure itself tells you what the plant does.

What happens to rejected product?

A detector is only useful if rejected product is kept apart. Ask these questions in writing.

  • Where does rejected product go, and is the reject bin locked?
  • Who examines a reject, and how is the finding recorded?
  • When metal is found, how does the plant locate and correct the source of the fragment?
  • What does the plant do with product made since the last passed check when a check fails?
  • Is a customer told about a confirmed foreign body finding that affects a shipped lot?

Which records should you request?

  1. The written procedure for detection, including test pieces, sizes, frequency and the action on failure.
  2. The verification log for the period around your lot, with date, time, operator and result for each test piece.
  3. The calibration or service record for the equipment.
  4. The reject log and the investigation records for any rejects on your lot.
  5. The extract of the hazard analysis that covers foreign bodies.

These records fit into the wider checks described in our guides to quality control from pond to sealed container and pre-shipment inspection.

How do you write this into a purchase specification?

A short clause is enough. State that the supplier runs metal detection, or X-ray where agreed, on the finished product or the packed carton. State the test-piece types and sizes that you and the supplier agree, the minimum verification frequency, and the action on a failed check. Add the right to see the verification log for your lot on request. Keep the clause in terms of what is checked and recorded. Leave brand names of equipment out.

A buyer whose customers require a particular scheme should check what the scheme requires for foreign body detection and pass the wording to the supplier before the first order. Detection equipment reduces the risk of a foreign body but does not remove it, so the clause belongs next to the supplier's other controls and not in place of them. This is general information. Confirm the requirements for your market with the competent authority.

FAQ

Does X-ray replace a metal detector?

Not by default. The two find different things. A metal detector finds metal. X-ray also finds dense non-metal objects such as glass, ceramic, bone and dense plastic. Some lines use one, some use both. Ask which materials the plant tests for and how often.

Is there a standard test-piece size?

We found no authoritative standard value. The right size depends on the equipment, the product and the pack. Ask the supplier for the sizes in its written procedure, and agree them with the supplier in the specification instead of assuming a figure.

What should I ask a seafood supplier about metal detection?

Ask where the detector sits on the line, which test pieces it uses and their sizes, how often it is verified, what happens to rejects and to product since the last good check, and which records you can see. Ask to see the log for your lot.

Sources

Send the specification you need to TBESFOOD, with product, form, size, packing and destination, and add your foreign body detection requirements. We will reply with a quotation and a timeline.

Let's Talk

Our team is available to answer your questions. Please fill out the form and we'll be in touch shortly.

*Please share the details of your request, and if applicable, the specific product you're interested in.

Email us

export@tbesfood.com

Call or WhatsApp

+84 932 072 978

TBESFOOD COMPANY LIMITED

A member of TBES Group

Head Office: 2nd Floor, 81 Cach Mang Thang 8 Street, Ben Thanh Ward, Ho Chi Minh City, Vietnam

Branch: 62/29C Lam Van Ben Street, Tan Hung Ward, Ho Chi Minh City, Vietnam

Factory: Lot C1.1, Cau Cang Phuoc Dong Industrial Zone, Hamlet 5, Phuoc Dong Commune, Can Duoc District, Long An Province

Lao Factory: Lao Yeast Factory, Ban Naphasouk, Xaythany District, Vientiane Capital, Lao PDR

TBES FOOD PTE. LTD.

Singapore Address: 470 North Bridge Road, #05-12, Bugis Cube, Singapore 188735

Sister brands: TbesAgri frozen fruit · TBESBY brewer's yeast · Lao Yeast Factory industrial ethanol

© 2016–2026 TBESFOOD COMPANY LIMITED. All rights reserved.

EspañolPrivacyCookie settings
FacebookEmailWhatsApp

TBESFOOD COMPANY LIMITED, a member of TBES Group