Share on

Sampling and Acceptance Criteria for Frozen Seafood: What to Agree Before Shipment

News

CN

Tbes Editorial Team

In short

Agree the sampling plan before shipment. Codex CXS 190 gives a model: AQL 6.5, a sample unit of at least 1 kg for individually quick frozen product, net weight measured frozen after removing the glaze, and a lot accepted only if defectives stay within the acceptance number and average net weight meets the declared weight.

What does an AQL of 6.5 mean for a lot?

An acceptable quality limit is the defect level a buyer tolerates when a lot is sampled. Codex CXS 190 uses AQL 6.5. A lot passes when the number of defective sample units does not exceed the acceptance number, written c, of the plan. The average net contents must also be at least the declared weight, with no unreasonable shortage in any pack, and the provisions on additives, hygiene and labelling must be met.

The sample size and the value of c come from the sampling table you name in the contract. Do not copy numbers from an article. Name the table, state the lot size basis and let both sides check it.

One limit on scope applies. CXS 190 covers quick frozen fish fillets offered for direct consumption and excludes product for further processing or industrial use. It is a usable template for pangasius fillet. It is not a shrimp standard, so agree shrimp defect criteria separately in the specification.

What counts as a defect in frozen fillets?

Defect criteria in Codex CXS 190-1995
AttributeDefective when
DehydrationMore than 10% of the surface area of the sample unit shows excessive moisture loss
ParasitesTwo or more per kg of sample unit
Bones, boneless packsMore than one bone per kg, 10 mm or longer
TexturePasty texture over 5% of the unit by weight, or gelatinous flesh over 86% moisture
Net weightAverage below declared weight, or unreasonable shortage in any pack
Lot decisionDefectives above c of the AQL 6.5 plan

For dehydration, Codex also sets the size of the affected area that counts as a defect. It is 25 cm² or more for packs of 200 g or less, 50 cm² or more for 201 to 500 g, and 150 cm² or more for 501 to 5,000 g.

How do you measure net weight on glazed product?

Codex determines net weight for each sample unit in the frozen state, without packaging. For glazed product the method removes the glaze under a gentle cold-water spray. A working procedure based on that method:

  1. Take the sample unit from frozen storage and record the frozen weight of the pack with glaze.
  2. Open the pack and remove the packaging.
  3. Hold the contents under a gentle spray of cold water until the ice layer is gone. The product must stay frozen.
  4. Pat the product dry and weigh it in a tared pan. This is the net weight.
  5. Calculate glaze: frozen weight with glaze minus net weight, divided by frozen weight with glaze, times 100.

Illustration: a pack weighs 1,000 g with glaze and 850 g after deglazing. The glaze is 150 g, which is 15 percent of the glazed weight and inside the 0 to 20 percent range. By the same arithmetic, a 10 kg glazed carton at 20 percent glaze holds 8 kg of fish. State in the contract whether glaze is a share of glazed weight or of net weight, because the two bases give different figures.

Two related notes cover the same arithmetic from the buyer side: how EU buyers check net weight on glazed shrimp and how net weight changes the cost of two quotes.

What should a sampling clause cover?

  1. Governing standard and specification version.
  2. Lot definition: one production lot or one batch code per shipment.
  3. Who draws the samples, when (at loading or at destination), how many cartons come from the agreed table, a sealed and signed sample record, and retained counter-samples.
  4. Sample unit: the primary pack, or at least 1 kg for individually quick frozen product.
  5. Defect classes (critical, major, minor) and the AQL for each class.
  6. Net weight and glaze method, declared glaze within 0 to 20 percent, and the basis stated in words.
  7. Temperature at receipt: core at or below -18 °C, with logger data supplied, and a rule for excursions.
  8. Laboratory testing: an accredited laboratory, the test panel, reporting limits and a decision rule.
  9. Claims: notification window, evidence required, a referee laboratory and the remedy.
  10. Records: lot codes with each shipment, kept longer than the shelf life.

When does an independent inspector help?

An independent inspection body suits large lots, a new supplier, or a trade where a dispute is likely. Name the body, the scope, the timing and the report format in the contract. IFST guidance adds two points for any result you receive: sampling often drives measurement uncertainty more than the method does, and a pass or fail statement should come with the decision rule behind it. Our pre-shipment inspection guide lists the checks done before the container is sealed. This note is general information. Adapt it with your own QA team and legal adviser.

FAQ

What is an AQL?

An acceptable quality limit is the defect level a buyer tolerates in a lot when sampling. Codex CXS 190 uses AQL 6.5. A lot passes if defective sample units stay within the acceptance number for the plan, and net weight and label rules are also met.

How is net weight checked on glazed fillets?

Weigh in the frozen state after removing the glaze. Open the pack, hold the contents under a gentle cold-water spray until the glaze is gone, pat dry and weigh in a tared pan. Net weight excludes glaze, and the average must not fall below the declared weight.

What counts as a defect in frozen fillets?

Codex CXS 190 lists dehydration over 10% of the surface area, two or more parasites per kg, more than one bone of 10 mm or longer per kg in boneless packs, and texture faults such as pasty flesh over 5% by weight. Add any further limits to your specification.

What should I put in a sampling clause for a frozen seafood contract?

Cover the lot definition, who draws samples, the sample size from a named AQL table, sealed retained samples, defect classes, the net weight and glaze method, core temperature at receipt, a referee laboratory, the claim period and the remedies.

Next step

Send TBESFOOD your specification: product, form, size, packing and destination. We will reply with a quote and a timeline.

Sources

Let's Talk

Our team is available to answer your questions. Please fill out the form and we'll be in touch shortly.

*Please share the details of your request, and if applicable, the specific product you're interested in.

Email us

export@tbesfood.com

Call or WhatsApp

+84 932 072 978

TBESFOOD COMPANY LIMITED

A member of TBES Group

Head Office: 2nd Floor, 81 Cach Mang Thang 8 Street, Ben Thanh Ward, Ho Chi Minh City, Vietnam

Branch: 62/29C Lam Van Ben Street, Tan Hung Ward, Ho Chi Minh City, Vietnam

Factory: Lot C1.1, Cau Cang Phuoc Dong Industrial Zone, Hamlet 5, Phuoc Dong Commune, Can Duoc District, Long An Province

Lao Factory: Lao Yeast Factory, Ban Naphasouk, Xaythany District, Vientiane Capital, Lao PDR

TBES FOOD PTE. LTD.

Singapore Address: 470 North Bridge Road, #05-12, Bugis Cube, Singapore 188735

Sister brands: TbesAgri frozen fruit · TBESBY brewer's yeast · Lao Yeast Factory industrial ethanol

© 2016–2026 TBESFOOD COMPANY LIMITED. All rights reserved.

EspañolPrivacyCookie settings
FacebookEmailWhatsApp

TBESFOOD COMPANY LIMITED, a member of TBES Group