Share on

Receiving Inspection for Frozen Seafood: A Warehouse Checklist

News

CN

Tbes Editorial Team

In short

A receiving inspection for frozen seafood checks four things at the dock: the goods are frozen and not partly thawed, the packaging is covered and undamaged, the dates are valid, and anything that fails is rejected. The FSANZ factsheet gives no numeric frozen limit and no probe method. Apply the limits in your own HACCP plan.

This page is a warehouse checklist for importers and cold-store operators who receive frozen pangasius, shrimp or other frozen seafood. It follows the logic of the food safety authority guidance we could read and adds general practice items, which are marked as such. It is general information, not a replacement for your food safety plan, your customer contract or advice from your local authority.

What does an authority say you must check on delivery?

The FSANZ factsheet on receiving food safely is short, and its frozen-food points are clear. Food delivered frozen must be frozen and not partly thawed. You check on delivery that it has not begun to thaw. You confirm that the food is covered or packaged, and that the covering is undamaged, because split or damaged packaging may indicate contamination. You reject food if the use-by date has passed. You also reject potentially hazardous food that does not meet the requirements.

Two things are absent from that page. It gives no numeric limit for frozen food. The 5 °C and 60 °C figures it uses apply to chilled and hot food. It also does not mention probes or any method for measuring core temperature. We therefore do not state a target temperature or a probe method here. Your HACCP plan, your customer specification and the rules of your competent authority set those values. Write them on your receiving form before the first delivery arrives.

What is the dock checklist, step by step?

The sequence below starts before the doors open and ends with a decision. Lines marked Practice come from common warehouse routine, not from the factsheet. The other lines follow the factsheet.

  1. Before arrival, hold the purchase order, the specification and the shipping documents at the receiving desk.
  2. Practice: compare the container number and the seal number on the doors with the documents before breaking the seal. Photograph the seal in place.
  3. Practice: read the reefer display and, where you have one, the data logger. Supply and return air readings can be compared with delivery conditions (Container Handbook).
  4. Open the doors and look first at the goods nearest the door. Check that the product is frozen and not partly thawed.
  5. Check that cartons and inner packs are covered and undamaged. Note any split, crushed or wet cartons by pallet position.
  6. Check the dates on the pack against the order and your remaining shelf-life requirement. Reject anything with an expired date.
  7. Practice: match carton labels to the specification and the delivery note. Check product name, size, net weight and lot code.
  8. Take core temperature readings as your HACCP plan requires, with your own calibrated equipment and your own limits.
  9. Decide: accept, accept with a note, hold for review, or reject. Record the decision, the reason and the person who made it.

How do you tell a thawing problem from a normal delivery?

The factsheet's test is simple: frozen, and not partly thawed. The source does not say how to spot refreezing, and no indicator is given for ice crystals or glaze condition. Do not invent criteria on the dock. Ask your QA lead to write down what your team looks at, such as free liquid in cartons, cartons that are soft or deformed, or product that has frozen into a block that does not match the pack form. Then test those criteria against your own supplier's agreed specification.

If you suspect a temperature excursion, the reefer record helps. The Container Handbook notes that data loggers hold supply and return air readings that can be compared with delivery conditions. The record supports a claim only if you read it at the time of receipt and keep a copy. Our guide to reefer temperature and loading covers the loading side of the same record.

Receiving inspection lines and the action for each
CheckWhat you look atAction if it fails
Frozen stateProduct frozen, not partly thawedHold or reject under your HACCP plan
PackagingCovered, undamaged, no splitsRecord by pallet position; reject damaged units
DatesDates valid against your requirementReject expired product
Container and seal (practice)Numbers match documentsPhotograph, stop unloading, call the supplier
Reefer record (practice)Display and logger read-outKeep a copy; compare with delivery conditions
Labels (practice)Match specification and delivery noteHold and raise with the supplier
Core temperaturePer your own method and limitPer your own HACCP plan

What does a reject or a hold decision involve?

The factsheet says to reject food that does not meet the requirements, and to reject it when the use-by date has passed. A good rejection record answers four questions for the supplier: what was wrong, how many cartons, where in the load, and what evidence you hold. Photographs of the seal, the cartons and the pack label, the logger read-out and the signed delivery note form that evidence.

A hold is different from a rejection. Product on hold stays frozen in a marked area while the QA lead decides. Set a time limit for the decision in your procedure. Tell the supplier the same day, because a prompt notice helps both sides check records while they are fresh. Keep any retained samples under the conditions your procedure sets.

What should the contract say about receiving?

A clear contract line helps avoid disputes at the dock. Agree before the first order what counts as acceptable condition on arrival, how many days you have to report a problem, which evidence you will send, and who pays for the retest if a sample goes to a laboratory. Agree how glaze is handled too. Use one term: glaze declared on the pack, with net weight stated without glaze, so that the weight you check matches the weight you pay for. Our note on net weight and glaze explains the check.

The documents you receive should also match the pack. The EU fish labelling guide lists the items a frozen pangasius or vannamei label shows. For what the supplier checks before the container is sealed, see our guide to pre-shipment inspection.

A receiving record template

Illustration: one line per delivery on a receiving form
FieldExample entryWhy it is recorded
Date and time of arrivalEntry made at the dockLinks the load to the logger read-out
Container and seal numbersEntered from the doorsMatches the shipping documents
Reefer display readingEntered as readStarts the temperature record
Condition of packagingIntact, or damage by pallet positionSupports a claim
Dates on packEntered per lotChecks the shelf-life requirement
Core temperature readingPer your HACCP methodShows control against your own limit
Decision and nameAccept, hold or reject, signedCreates accountability

The table is an illustration of a form layout. The entries are examples of what to record, not limits or readings.

FAQ

What temperature should frozen seafood be at when it arrives?

The FSANZ factsheet requires frozen food to be frozen and not partly thawed, and gives no numeric frozen limit. Use the limit in your HACCP plan, your customer specification and the rules of your competent authority. Write that limit on the receiving form so that every shift applies the same value.

Do I need a probe thermometer at receiving?

The source we read does not mention probes. Whether you measure core temperature, and how, is a decision for your HACCP plan and your authority's rules. If your plan requires it, keep the equipment calibrated and record each reading with the lot and the time.

How do I check a frozen seafood delivery before accepting it?

Check that the goods are frozen and not partly thawed, that packaging is covered and undamaged, and that dates are valid. Compare container and seal numbers with the documents, read the reefer record, and match labels to the specification. If anything fails, hold or reject and record the evidence.

Can TBESFOOD share a receiving specification with the order?

We can state pack format, labelling and glaze terms in the specification so your receiving team knows what to expect. The acceptance limits remain yours. Send your receiving form and we will match the specification lines to it before the first shipment.

Sources

Send the specification to TBESFOOD for a quote and timeline: product, form, size, packing and destination. Include your receiving requirements so we can align the pack and documents.

Let's Talk

Our team is available to answer your questions. Please fill out the form and we'll be in touch shortly.

*Please share the details of your request, and if applicable, the specific product you're interested in.

Email us

export@tbesfood.com

Call or WhatsApp

+84 932 072 978

TBESFOOD COMPANY LIMITED

A member of TBES Group

Head Office: 2nd Floor, 81 Cach Mang Thang 8 Street, Ben Thanh Ward, Ho Chi Minh City, Vietnam

Branch: 62/29C Lam Van Ben Street, Tan Hung Ward, Ho Chi Minh City, Vietnam

Factory: Lot C1.1, Cau Cang Phuoc Dong Industrial Zone, Hamlet 5, Phuoc Dong Commune, Can Duoc District, Long An Province

Lao Factory: Lao Yeast Factory, Ban Naphasouk, Xaythany District, Vientiane Capital, Lao PDR

TBES FOOD PTE. LTD.

Singapore Address: 470 North Bridge Road, #05-12, Bugis Cube, Singapore 188735

Sister brands: TbesAgri frozen fruit · TBESBY brewer's yeast · Lao Yeast Factory industrial ethanol

© 2016–2026 TBESFOOD COMPANY LIMITED. All rights reserved.

EspañolPrivacyCookie settings
FacebookEmailWhatsApp

TBESFOOD COMPANY LIMITED, a member of TBES Group